Hammerite Rust Cap 42245 Rust Preventative Spray Paint, 12 Oz, Gray

---

DESCRIPTION

HAMMERITE RUST CAP SMOOTH ENAMEL FINISH is a self-priming, rust preventive coating designed to provide long-lasting metal protection. It provides a decorative finish that resists corrosion and the damaging effects from moisture and severe weather, and is formulated for interior and exterior use.

Highlights :

• Size: 12 Oz.
• Color: Gray
• Self priming, quick dry enamel
• Encapsulates rust
• No primer needed, paint right over rust
• With Glassguard for maximum protection. Home, auto, farm, marine, property maintenance
• One step and the rust is history
• Dry time to touch 30 minutes, recoats should be applied within 4 hours
• Smooth finish

Where to Use :

• For use on metal substrates
• Can be applied directly over firm, rusty surfaces
• For previously painted surfaces, apply HAMMERITE® RUST CAP® SMOOTH ENAMEL FINISH to a small area first to check adhesion and test for lifting or cracking

Surface Preparation :

• Prepare surface by removing dirt, grease, wax, moisture, rust, loose paint and any other contamination that can affect the coating's adhesion. If washing is necessary, use a non-soapy detergent or TSP substitute. Rinse well and allow to dry
• Scrape off loose paint and rust with a wire brush
• Scuff sand rusted, glossy or hard surfaces

Application :

• Eye protection is recommended
• Do not thin
• Use in a well-ventilated area when temperature is between 60°F and 80°F and humidity is below 60% to ensure proper drying
• Mix paint thoroughly before and during application
• Always maintain a wet edge, but avoid over-brushing and/or rolling
• Apply 2 or more coats as needed to achieve the 4 mil dry film thickness
• Recoat after the first coat has dried to the touch (30-45 minutes)
• Use a high quality ¼” nap Mohair cover on smooth surfaces. A quality synthetic bristle brush can also be used
• Airless Spray: Use .017-.021 tip size at approximately 1800-2600 psi
• Conventional Spray: Use 70-80 thousandths tip size, pot pressure 15-20 psi and atomizing pressure 25-35 psi

Dry Time & Coverage :

• Each additional coat must be applied within 4 hours or after 14 days of drying
• Dries to the touch in 90 minutes
• Coverage is approximately 200 sq. ft. per gallon depending on the method of application, porosity and texture of the surface (to achieve a 4 mil dry film thickness)

Clean Up & Disposal :

• Clean all tools, equipment and paint spatters with Xylene or lacquer thinner
• If spilled, contain material and remove with an inert absorbent
• Dispose of contaminated absorbent, container and unused product in accordance with all current federal, state and local regulations
• Do not dispose of this product down a drain
• Please consider donating any unused product

Aerosol Application :

• Use outdoors or in a well-ventilated area when temperature is between 60°F and 80°F and humidity is below 60% to ensure proper drying. Avoid spraying in very windy or dusty conditions
• Shake can vigorously for 2 minutes after mixing ball begins to rattle and often during use. Hold can upright, moving from side-to-side while spraying lightly and evenly about 12” from area being painted. Ensure corners, edges and heavily pitted areas are adequately covered. Apply 3 or more light coats allowing 10 to 15 minutes between coats

Aerosol Dry Time & Coverage :

• Dries in 15 minutes or less
• Handle after one hour
• Recoat should be done within 1 hour or after 10 days
• A 4 mil coating cures in 14 days
• Coverage is up to 18 sq. ft

Aerosol Clean Up & Disposal :

• Clear spray valve immediately after use by turning can upside down and spraying until only clear gas is released
• If spray nozzle becomes clogged, remove and clean with mineral spirits. Gently replace spray button with a twisting motion, with top of can and valve opening pointed away from you. Do not stick pins or wire into can opening
• Do not dispose of this product down a drain
• Please consider donating any unused product

Glassguard® Protection :

• As the coating dries, microscopic heat-hardened glass flakes interlock with special resins forming a super-tough barrier that seals out moisture to prevent rusting